Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Yoshikawa, Ryuji; Imai, Yasutomo*; Kikuchi, Norihiro; Tanaka, Masaaki; Ohshima, Hiroyuki
Nuclear Technology, 210(5), p.814 - 835, 2024/05
In the study of safety enhancement on advanced sodium-cooled fast reactor, it is essential to clarify the thermal-hydraulics under various operation conditions in a fuel assembly (FA) with the wire-wrapped fuel pins to assess the structural integrity of the fuel pin. A finite element thermal-hydraulics analysis code named SPIRAL has been developed to analyze the detailed thermal-hydraulics phenomena in a FA. In this study, the numerical simulations of the 37-pin bundle sodium experiments at different Re number conditions, including a transitional condition between laminar and turbulent flows and turbulent flow conditions, were performed to validate the hybrid turbulence model equipped in SPIRAL. The temperature distributions predicted by SPIRAL was consistent with those measured in the experiments. Through the validation study, the applicability of the hybrid turbulence model in SPIRAL to thermal-hydraulic evaluation of sodium-cooled FA in the wide range of Re number was confirmed.
Kawaguchi, Munemichi; Hirakawa, Yasushi; Sugita, Yusuke; Yamaguchi, Yutaka
Nuclear Technology, 210(1), p.55 - 71, 2024/01
Times Cited Count：0 Percentile：0.01(Nuclear Science & Technology)This study has developed an estimation method for residual sodium film and sodium lumps on dummy fuel pins in Monju and demonstrated sodium draining behavior through gaps among the pins, experimentally. The amounts of the residual sodium on the surface of the pins were measured using the three-type test specimens: (a) single pin, (b) 7-pin assembly, and (c) 169-pin assembly. The experiments revealed that the withdrawal speed of the pins and improvement of the sodium wetting increased drastically the amounts of the residual sodium. Furthermore, the experiments using the 169-pin assembly measured the practical amounts of the residual sodium in the dummy fuel assembly of short length and demonstrated sodium draining behavior through the dummy fuel assembly. The estimation method includes four models: a viscosity flow model, Landau-Levich-Derjaguin (LLD) model, an empirical equation related to the Bretherton model, and a capillary force model in a tube. The calculation predicted comparable amounts of the residual sodium with the experiments. An uncertain of the sodium wetting effects were close to 1.8 times the estimation values of the LLD model. With this estimation method, the amounts of the residual sodium on the unloaded Monju dummy fuel assembly can be evaluated.
Kosaka, Wataru; Uchibori, Akihiro; Okano, Yasushi; Yanagisawa, Hideki*
Proceedings of 20th International Topical Meeting on Nuclear Reactor Thermal Hydraulics (NURETH-20) (Internet), p.1150 - 1163, 2023/08
The leakage of pressurized water from a steam generator (SG) and the progress after that are a key issue in the safety assessment or design of a SG in sodium-cooled fast reactor. The analysis code LEAP-III can evaluate a rate of water leakage during the long-term event progress, i.e., from the self-wastage initiated by an occurrence of a microscopic crack in a tube wall to the water leak detection and water/water-vapor blowdown. Since LEAP-III consists of semi-empirical formulae and one-dimensional equations of conservation, it has an advantage in short computation time. Thus, LEAP-III can facilitate the exploration of various new SG designs in the development of innovative reactors. However, there are several problems, such as an excessive conservative result in some case and the need for numerous experiments or preliminary analyses to determine tuning parameters of models in LEAP-III. Hence, we have developed a Lagrangian particle method code, which is characterized by a simpler computational principle and faster calculation. In this study, we have improved the existing particle pair search method for interparticle interaction in this code and developed an alternative model without the pair search. Through the trial analysis simulating in a tube bundle system, it was confirmed that new models reduced the computation time. In addition, it was shown that representative temperatures of the heat-transfer tubes evaluated by this particle method code, which is used to predict the tube failure in LEAP-III, were good agreement with that by SERAPHIM, which is a detailed mechanistic analysis method code.
Li, C.-Y.; Wang, K.*; Uchibori, Akihiro; Okano, Yasushi; Pellegrini, M.*; Erkan, N.*; Takata, Takashi*; Okamoto, Koji*
Applied Sciences (Internet), 13(13), p.7705_1 - 7705_29, 2023/07
Times Cited Count：1 Percentile：0(Chemistry, Multidisciplinary)Kurisaka, Kenichi; Nishino, Hiroyuki; Yamano, Hidemasa
Proceedings of 30th International Conference on Nuclear Engineering (ICONE30) (Internet), 8 Pages, 2023/05
The objective of this study is to develop an effectiveness evaluation methodology of the measures for improving resilience of nuclear structures against excessive earthquake by applying the failure mitigation technology. This study regarded those measures for improving resilience of important structures, systems, and components for safety to enlarge their seismic safety margin. To evaluate effectiveness of those measures, seismic core damage frequency (CDF) is selected as an index. Reduction of CDF as an effectiveness index is quantified by applying seismic PRA technology. Accident sequences leading to loss of decay heat removal are significant contributor to seismic CDF of sodium-cooled fast reactors (SFRs), and those sequences result in core damage via ultra-high temperature condition. This study improved the methodology to evaluate not only the measures against shaking due to excessive earthquake but also the measures at the ultra-high temperature condition. To examine applicability of the improved methodology, a trial calculation was implemented with some assumptions for a loop-type SFR. Within the assumption, the measures for improving resilience were significantly effective for decreasing CDF in excessive earthquake up to several times of a design basis ground motion. Through the applicability examination, the methodology for the effectiveness evaluation was developed successfully.
Kurisaka, Kenichi
Proceedings of 30th International Conference on Nuclear Engineering (ICONE30) (Internet), 10 Pages, 2023/05
This study aims to understand a time trend of the occurrence rate of steam generator (SG) tube leak in the existing sodium-cooled fast reactors (SFRs) based on the observed data. The target on SFRs in the present paper is Phenix in France and BN600 in Russia. From the open literature review, we investigated the number of tube-to-tube plate weld, the number of tube-to-tube weld, heat transfer area of tube base metal, operating time of SGs, dates when SG tube leak occurred, leaked location, corrective action after tube leak such as replacement of leaked module. Based on these observed data, time to leak is estimated and then time trend of the occurrence rate of SG tube leak for each of the above-mentioned parts was quantitatively analyzed by the hazard plotting method. As a result, the rate of leak at tube-to-tube weld in Phenix shows increase with time due to probable cause of cyclic thermal stress in a short term. As for a long-term trend, the rate of tube leak in both Phenix and BN600 SGs indicated decrease with time probably thanks to improvement in welding and in SG operating condition and to removal of initial failure.
Li, C.-Y.; Watanabe, Akira*; Uchibori, Akihiro; Okano, Yasushi
Proceedings of 30th International Conference on Nuclear Engineering (ICONE30) (Internet), 10 Pages, 2023/05
Kubo, Shigenobu; Chikazawa, Yoshitaka; Ohshima, Hiroyuki; Kamide, Hideki
Handbook of Generation IV Nuclear Reactors, Second Edition, p.173 - 194, 2023/03
Handbook of Generation IV Nuclear Reactors, Second Edition is a fully revised and updated comprehensive resource on the latest research and advances in generation IV nuclear reactor concepts. Editor Igor Pioro and his team of expert contributors have updated every chapter to reflect advances in the field since the first edition published in 2016. JAEA contributes to Chapter 5; Sodium-cooled Fast Reactors (SFRs) and Chapter 12; Generation-IV Sodium-cooled Fast Reactor (SFR) concepts in Japan. Major characteristics and current technology developments including safety enhancement were described in Chapter 5. Chapter 12 shows design activities of SFR. Innovative technology developments, and update of the Japan sodium-cooled fast reactor design with lessons learned from the TEPCO Fukushima Daiichi NPP accident.
Kobayashi, Jun; Aizawa, Kosuke; Ezure, Toshiki; Nagasawa, Kazuyoshi*; Kurihara, Akikazu; Tanaka, Masaaki
JAEA-Research 2022-009, 125 Pages, 2023/01
JAEA-Research-2022-009.pdf:29.22MB
The design studies of an advanced loop-type sodium-cooled fast reactor (Advanced- SFR) have been carried out by the Japan Atomic Energy Agency (JAEA). At the core outlet, temperature fluctuations occur due to mixing of hot sodium from the fuel assembly with cold sodium from the control rod channels and radial blanket assembly. These temperature fluctuations may cause high cycle thermal fatigue around a bottom of Upper Internal Structure (UIS) located above the core. Therefore, we conducted a water experiment using a 1/3 scale 60 degree sector model that simulated the upper plenum of the advanced loop-type sodium-cooled reactor. And we proposed some countermeasures against large temperature fluctuations that occur at the bottom of the UIS. In this report, we have summarized that the effect of the countermeasure structure to mitigate the temperature fluctuation generated at the bottom of UIS is confirmed, and the Reynolds number dependency of the countermeasure structure and the characteristics of the temperature fluctuation on the control rod surface.
Ishida, Shinya; Fukano, Yoshitaka; Tobita, Yoshiharu; Okano, Yasushi
Journal of Nuclear Science and Technology, 13 Pages, 2023/00
Times Cited Count：1 Percentile：0.01(Nuclear Science & Technology)Li, C.-Y.; Watanabe, Akira*; Uchibori, Akihiro; Okano, Yasushi
Journal of Nuclear Science and Technology, 23 Pages, 2023/00
Times Cited Count：1 Percentile：72.91(Nuclear Science & Technology)Emura, Yuki; Takai, Toshihide; Kikuchi, Shin; Kamiyama, Kenji; Yamano, Hidemasa; Yokoyama, Hiroki*; Sakamoto, Kan*
Journal of Nuclear Science and Technology, 10 Pages, 2023/00
Times Cited Count：0 Percentile：0.01(Nuclear Science & Technology)Zhang, T.*; Morita, Koji*; Liu, X.*; Liu, W.*; Kamiyama, Kenji
Annals of Nuclear Energy, 179, p.109389_1 - 109389_10, 2022/12
Times Cited Count：1 Percentile：31.61(Nuclear Science & Technology)Tsuji, Mitsuyo; Aizawa, Kosuke; Kobayashi, Jun; Kurihara, Akikazu
Proceedings of 12th Japan-Korea Symposium on Nuclear Thermal Hydraulics and Safety (NTHAS12) (Internet), 6 Pages, 2022/10
In sodium-cooled fast reactors (SFRs), decay heat removal after a core disruptive accident (CDA) is an important issue for the safety enhancement. Therefore, water experiments using a 1/10 scale experimental apparatus (PHEASANT) that simulates the reactor vessel of an SFR are conducted to investigate the natural circulation phenomena in the reactor vessel. In this study, experiments under the operation of the dipped-type DHX were conducted to investigate the effect of the heat generation ratio between the fuel debris on the core catcher in lower plenum and the reactor core remnant on the natural circulation behavior in the reactor vessel. The temperature distribution and the velocity distribution were measured under two heat generation conditions. Thus, the effect of the heat generation ratio between the fuel debris in the lower plenum and the reactor core remnant on the natural circulation behavior was quantitatively grasped under the dipped-type DHX operating conditions.
Onoda, Yuichi; Yamano, Hidemasa
Proceedings of 12th Japan-Korea Symposium on Nuclear Thermal Hydraulics and Safety (NTHAS12) (Internet), 9 Pages, 2022/10
In Japan, sodium-cooled fast reactor design takes In-Vessel Retention (IVR) strategy to stably cool damaged core materials in the reactor vessel during a severe accident with various design measures. Although a possibility to fail IVR is extremely low, a probabilistic risk assessment study needs a wide variety of scenarios including the IVR failure. Therefore, in order to study a wide range of event spectra related to stable cooling of debris in the reactor vessel, this study numerically investigated the deformation and failure behavior of the reactor vessel due to the debris deposited onto the skirt of the core catcher using the FINAS-STAR structural analysis code. The analyses are conducted in two cases of power density with the aim of investigating failure conditions of the bottom of the reactor vessel. Reactor vessel deforms significantly when the temperature reaches about 1100 
C and the reactor vessel reaches the failure criteria in high-power-density case.
Futagami, Satoshi; Kubo, Shigenobu; Sofu, T.*; Ammirabile, L.*; Gauthe, P.*
Proceedings of International Conference on Topical Issues in Nuclear Installation Safety; Strengthening Safety of Evolutionary and Innovative Reactor Designs (TIC 2022) (Internet), 10 Pages, 2022/10
Kato, Shinya; Matsuba, Kenichi; Kamiyama, Kenji; Akaev, A.*; Vurim, A.*; Baklanov, V.*
Proceedings of 13th International Topical Meeting on Nuclear Reactor Thermal-Hydraulics, Operation and Safety (NUTHOS-13) (Internet), 12 Pages, 2022/09
The In-Vessel Retention (IVR) of molten-core in Core Disruptive Accidents (CDAs) is of prime importance in enhancing the safety of sodium-cooled fast reactors. One of the main subjects in ensuring IVR is to design the Control Rod Guide Tube (CRGT) which allows effective discharge of molten core materials from the core region. The effectiveness of the CRGT design is assessed through CDA analyses, and it is reasonable for these analyses to develop a computer code collaborated with experimental researches. Thus, experiments addressing the discharge behavior of the molten-core materials through the CRGT have proceeded as one of the subjects in the collaboration research named the EAGLE-3 project, and the obtained experimental results are reflected in the development of the SIMMER code. In this project, a series of out-of-pile tests using molten-alumina as the fuel simulant was conducted to understand the discharge behavior of molten-core materials through the CRGT. In this study, in order to investigate the effect of an internal structure in the CRGT on the discharge behavior of the molten-core materials, the data of an out-of-pile test in which the molten-alumina penetrated to a duct with the internal structure were analyzed. In addition, the post-test analysis using the SIMMER code was conducted and the results were compared with the test results.
Matsushita, Hatsuki*; Kobayashi, Ren*; Sakai, Takaaki*; Kato, Shinya; Matsuba, Kenichi; Kamiyama, Kenji
Proceedings of 13th International Topical Meeting on Nuclear Reactor Thermal-Hydraulics, Operation and Safety (NUTHOS-13) (Internet), 9 Pages, 2022/09
During core disruptive accidents in sodium-cooled fast reactors, the molten core material flows through flow channels, such as the control rod guide tubes, into the core inlet plenum under the core region. The molten core material can be cooled and solidified while impinging on a horizontal plate of the inlet plenum in a sodium coolant. However, the solidification and cooling behaviors of molten core materials impinged on a horizontal structure have not been sufficiently studied thus far. Notably, this is an important phenomenon that needs to be elucidated from the perspective of improving the safety of sodium-cooled fast reactors. Accordingly, a series of experiments on discharging a simulated molten core material (alumina: Al
O
) into a sodium coolant on a horizontal structure was conducted at the experimental facility of the National Nuclear Center of the Republic of Kazakhstan. In this study, analyses on the sodium experiments using SIMMER-III as the fast reactor safety evaluation code were performed. The analysis methods were validated by comparing the results and experiment data. In addition, the cooling and solidification behaviors during jet impingement were evaluated. The results indicated that the molten core material exhibited fragmentation owing to the impingement on the horizontal plate and was, therefore, scattered toward the periphery. Furthermore, the simulated molten core material was evaluated to be cooled by sodium and subsequently solidified.
Doi, Daisuke
Proceedings of 29th International Conference on Nuclear Engineering (ICONE 29) (Internet), 7 Pages, 2022/08
Matsushita, Kentaro; Ezure, Toshiki; Imai, Yasutomo*; Fujisaki, Tatsuya*; Tanaka, Masaaki
Proceedings of 29th International Conference on Nuclear Engineering (ICONE 29) (Internet), 8 Pages, 2022/08
Development of evaluation method for cover gas entrainment (GE) by vortices generated at free surface in upper plenum of sodium-cooled fast reactor (SFR) is required. GE evaluation tool, named StreamViewer, based on method using numerical results of three-dimensional computational fluid dynamics analysis for loop-type SFRs has been developed. In this study, modification of evaluation method of StreamViewer to rationalize conservativeness in evaluation results was examined by identifying vortex center lines and calculating three-dimensional distribution of pressure decrease along vortex center lines. The applicability of modified method was checked using water experimental result in rectangular open channel where unsteady vortices are generated. As the result, it was indicated that evaluation results on gas core depth which were excessive in current method were improved in modified method, and it is confirmed that modified method may discriminate onset of GE with appropriate criteria.
